motorola
BEFOREYOU BEGIN
Before using this product, read the Important Safety and Legal
Information pamphlet and follow its instructions.
®
Bluetooth
Handsfree Headset
Take a moment before you get started to
familiarize yourself with your new
H550 Headset.
Call Button/
Slide Switch
Multi-Color
Indicator Light
Volume
Buttons
Microphone
Speaker
(on reverse
side)
H550
Get connected in 4 quick steps.
CHARGE
START BLUETOOTH
1
2
Your Headset's Battery
FEATURE
Your Phone
Charging
Port
Your phone's Bluetooth feature is off by default.
To use your headset, you must turn on the
Bluetooth feature in your phone.
For most Motorola phones (at the main menu):
M
Press
(Menu) > Settings > Connection >
1
Verify slide switch is in the off position (toward
the charging port).
1
2
Bluetooth Link > Setup.
Scroll to Power.
Select Change.
Scroll to On.
Plug the Motorola charger into the end of the
headset.
2
3
4
5
The indicator light turns red when the battery is
charging. It may take up to 1 minute for the
indicator light to turn on. When the headset's
battery is fully charged (about 2 hours), the
indicator light turns off.
Press Select to turn on the Bluetooth
feature.The Bluetooth feature remains on
until you turn the feature off.
Disconnect the charger.
Note: Headset is not functional while charging.
3
Note: For optimal performance, make sure that the
headset is off while charging.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
TROUBLESHOOTING
USING YOUR H550
My headset will not enter pairing mode.
Make sure that any devices previously paired
with the headset are turned off. If the indicator
light is not steadily lit in blue, turn off both the
other device and headset, wait 10 seconds,
then turn headset back on. Wait for the indicator
light to become steadily lit in blue, indicating
the headset is now in pairing mode.
See
Features and
Functions Guide
on the reverse side
for information on
using your H550
My phone doesn't find my headset.
Make sure the indicator light on your headset is
on (lit in blue) and steady when your phone is
searching for devices (see step 3).
My headset worked before but now it's not
working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (see step 2).
If the Bluetooth feature was turned off or was
turned on only temporarily, you may need to
restart the Bluetooth feature (see step 2) and
pair your phone and headset again (see step 3).
Note: If desired, your headset can be restored to original
factory settings.This action will erase all pairing information
stored in your headset.Thus, you will need to pair your
phone and headset again (see step 3).
Support.
To restore your headset to original factory settings, press
and hold both Volume buttons and the Call button at the
same time for 10 seconds.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
TURNING HEADSET
ON AND OFF
Features and
Functions Guide
To turn your headset on, slide the switch
toward the microphone.The indicator light is
steadily purple for several seconds, then
flashes blue (if paired and connected with
another device) or is steadily blue (if ready
to be paired).
H550
Bluetooth®
Handsfree Headset
To turn your headset off, slide the switch
toward the charging plug. The indicator light
will turn off.
IMPORTANT:
Be sure to first follow the
Slide Switch
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H550.
Indicator Light
EARHOOKS ANDYOUR
HEADSET
WEARINGTHE
HEADSET
Your H550 headset is supplied with multiple
earhooks.The earhook is attached onto a hinge pin,
and is placed onto your ear when using your
headset.To install an earhook on your headset:
Once you have attached your desired
earhook, follow these steps to wear your
headset on your ear:
1
Open the attached
earhook 45 degrees from
the headset.
1
Open the attached
earhook 90 degrees from
the headset.
1
2
3
Loop the earhook over
your ear.
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin.Then, pull it away to
remove it.
2
Press earhook to your ear.
1 Open Earhook
2
When worn, your headset
will look like this on your
head:
2 Pull Earhook Up
3
Position the headset for
right or left ear use (right
ear use is displayed).
3
4
Hinge Pin
Hook the bottom of the
earhook onto the lower
hinge pin, then lift and pull
the top of the earhook
over the upper hinge pin.
CHANGINGVOLUME
European Union Directives
Conformance Statement
BUTTON ORIENTATION
Hereby, Motorola declares that this
product is in compliance with:
You can also change the orientation of the
volume buttons on your headset.
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
Turn the headset power off.
1
2
• All other relevant EU Directives.
Press and hold the Volume button you
want to assign as the "volume up" button
and slide the switch toward the
microphone.The indicator light is either
steadily lit or flashing in blue.
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
Volume
Buttons
Slide
Switch
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
product Approval Number from your product’s label in
the “Search” bar on the web site.
MAKING CALLS
MAKING CALLS CONTINUED
Function
Action
Function
Action
Receive a call
Tap the Call button
Answer a second
incoming call
Tap the Call button
Mute or unmute a call
Tap both Volume
buttons
End an active call and
resume a call on hold
Tap the Call button
Reject a call
Press and hold a
Volume button until
you hear two
Disable the
indicator light
First slide the switch
toward charging plug
(to turn headset off),
then press and hold
both Volume
buttons AND slide
the switch towards
the microphone (to
turn headset on)
descending tones
End a call
Tap the Call button
Redial last call
Press and hold the
Call button until you
hear two ascending
tones
Make a voice dial call
Tap the Call button
and speak the
name after the tone
Note: Some features are phone/network dependent.
Note:Your H550 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
INDICATOR LIGHTS
AUDIOTONES
With the Charger Plugged In
AudioTone
Headset Status
Headset Indicator
Steady red
Off
Headset Status
Charging
Charging complete
Ring tone
Incoming call
Single high tone
Phone network not
available
With No Charger Plugged In
Headset Indicator
Off
High to low tone
End call
Headset Status
Power off
Powering up
Single high tone when
pressing volume button
Volume at minimum
or maximum
Steady purple
Two ascending tones
Two descending tones
Low to high tone
Mute enabled
Mute disabled
Steady blue
Pairing/connection
mode
Connection successful
Standby (not on call)
Incoming call
Connection
confirmation/voice
activation
10 rapid purple flashes
Slow blue flash
Quick blue flash
Slow blue pulse
No audio indications;
deteriorating quality
Out of range
Connected (on a call)
Slow purple pulse
Connected
Two tones
repeated every 30 sec.
Low battery
(on a muted call)
Red flash
Idle (not connected)
Quick red flash
Low battery
Note: After 30 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
|