RocketFish Speaker RF ES02 User Guide

Digital Wireless Speakers  
RF-WS01/WS01-W/WS02  
User Guide  
 
Your RF-WS01, RF-WS01-W, or RF-WS02 Digital Wireless Speakers use  
a proprietary 2.4GHz wireless communication system to transmit  
low-latency, high fidelity audio from an audio source to wireless  
speakers, providing a superior level of audio quality and resistance to  
interference.  
The system accepts line-level inputs, and is compatible with a  
complete range of multi-channel home theatre systems or AV  
receivers.  
Safety information  
CAUTION  
Risk of Electric Shock  
Do Not Open  
This lightning flash with the arrowhead symbol within an  
equilateral triangle is intended to alert the user to the  
presence of uninsulated dangerous voltage within the  
product’s enclosure that may be of sufficient magnitude to  
constitute a risk of electric shock to persons.  
The exclamation point within an equilateral triangle is  
intended to alert the user to the presence of important  
operating and maintenance (servicing) instructions in the  
literature accompanying the product.  
CAUTION  
To reduce the risk of electric shock, do not remove the cover (or the  
back). There are no user-serviceable parts inside. Refer servicing to  
qualified service personnel.  
Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to  
rain or moisture.  
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
Follow all instructions.  
Do not use this apparatus near water.  
Clean only with a dry cloth.  
RF-WS01/WS01-W/WS02  
 
3
Do not block any ventilation openings. Install in accordance with the  
manufacturer's instructions.  
Do not install near any heat sources such as radiators, heat registers,  
stoves, or other apparatus (including amplifiers) that produce heat.  
Do not defeat the safety purpose of the polarized or grounding-type  
plug. A polarized plug has two blades with one wider than the other. A  
grounding type plug has two blades and a third grounding prong. The  
wide blade or the third prong is provided for your safety. If the provided  
plug does not fit into your outlet, consult an electrician for replacement  
of the obsolete outlet.  
Protect the power cord from being walked on or pinched particularly at  
plugs, convenience receptacles, and the point where they exit from the  
apparatus.  
Only use attachments or accessories specified by the manufacturer.  
Use only with the cart, stand, tripod, bracket, or table  
specified by the manufacturer, or sold with the apparatus.  
When a cart is used, use caution when moving the cart and  
apparatus combination to avoid injury from tip-over.  
Unplug this apparatus during lightning storms or when  
unused for long periods of time.  
Refer all servicing to qualified service personnel. Servicing is required  
when the apparatus has been damaged in any way, such as  
power-supply cord or plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped.  
The apparatus shall not be exposed to dripping or splashing and no  
objects with liquids such as vases, shall be placed on the apparatus.  
The AC power adapter is used as the disconnect device. This disconnect  
device shall remain readily operable.  
Read the Rating labels on the bottom of the base station and wireless  
speaker for power input and other safety information.  
4
 
Features  
2.4 GHz wireless sender and speaker  
Transmits high quality audio over a radio frequency communication link  
Compact size  
Hidden antennas  
Low power consumption  
Package contents  
Examine the contents of the box for your Rocketfish Digital Wireless  
Speakers. The box should contain.  
A sender unit  
One speaker (RF-WS02) or two speakers (RF-WS01, and RF-WS01-W  
An AC power adapter for the sender unit  
One (RF-WS02) or two (RF-WS01 and RF-WS01-W) AC power adapter(s)  
for the speakers  
A User Guide  
Sender  
The sender transmits audio signals over a 2.4 GHz radio frequency  
carrier to the speaker.  
RF-WS01/WS01-W/WS02  
 
5
 
Front view  
1
Item Description  
1
Power and link Status LED—GREEN  
Side view  
1
Item Description  
1
Power ON/OFF switch with Status LED  
6
 
Back view  
1
2 3  
Item Description  
1
2
3
RCA audio input terminals  
DC IN jack  
Pairing (manual connect) button  
Speaker  
The speaker receives the 2.4 GHz audio signals from the sender and  
plays out the sound using the built-in amplifier and speakers. The  
speaker can operate from the supplied AC adapter or from batteries.  
RF-WS01/WS01-W/WS02  
 
7
Front (RF-WS01/RF-WS01-W)  
1
2
3
Item Description  
1
2
3
Power ON/OFF switch with Status LED  
Volume control  
Left/Mono/Right control  
8
 
Back (RF-WS01/RF-WS01-W)  
1
2
Item Description  
1
2
DC IN jack  
Pairing (manual connect) button  
RF-WS01/WS01-W/WS02  
 
9
Front (RF-WS02)  
1
2
4
5
6
3
7
Item Description  
1
LED:  
Solid green—Connected to AC power  
Quick flashing—Pairing mode  
Slow flashing—No link  
Red—Low battery  
2
3
Bass Boost LED—RED  
Charging LED:  
Flashing green—Charging  
Solid green—Charging complete  
4
5
6
7
Power ON/OFF switch  
Bass Boost control button  
Speaker output selector (Left/Mono/Right) switch  
Volume control  
10  
 
Back (RF-WS02)  
1
2
Item Description  
1
2
Pairing (manual connect) button  
DC IN jack  
RF-WS01/WS01-W/WS02  
 
11  
Setting up your system  
Caution: Turn off your audio source while connecting the units  
Connecting the sender  
To connect the sender to an audio source:  
1
Connect a stereo RCA cable from an audio source to the sender taking  
care to match white and red colors at both ends. Make sure that the  
cable is connected to an audio source and not a video source.  
To right and  
left input jack  
To right and left  
output jack  
2
Connect the AC adapter connector to the sender DC IN jack.  
Caution: To avoid risk of fire, and to prevent damage, only use the AC adapter  
supplied with your digital wireless speakers. Make sure that power supply outlet  
matches the AC adapter’s 120V before making the connection.  
Plug the AC power  
adapter in only after  
your audio source is  
connected to the  
sender.  
DC IN 5V  
12  
 
 
Connecting the speakers  
Plug the AC power adapter in if batteries are not being used or if the  
batteries are discharged.  
Caution: To avoid risk of fire, and to prevent damage, only use the AC adapter  
supplied with your digital wireless speakers. Make sure that power supply outlet  
matches the AC adapter’s 120V before making the connection.  
To connect the AC adapter to your speakers:  
Connect the AC adapter connector to the speaker DC IN jack.  
RF-WS01 & RF-WS01-W  
RF-WS02  
RF-WS01/WS01-W/WS02  
 
13  
Installing batteries into the speakers  
Caution: Do not mix battery types. Do not use old and new batteries together.  
Remove all batteries if the unit is not going to be used for a long period of time.  
1
2
With the speaker AC adapter disconnected, open the battery cover.  
Install eight (8) C size batteries taking care to follow the battery polarity  
markings on the battery compartment.  
3
For WS-02, set the Alkaline/NiMH battery switch to the type of C size  
batteries being used. The switch is inside the battery compartment. Use  
the Alkaline setting if you are using standard non-rechargeable alkaline  
batteries. Use the NiMH setting if you are using rechargeable NiMH  
batteries.  
4
Replace the battery cover. When charging (speakers on or off), the LED  
flashes green slowly. When charging is complete, the LED lights solid  
green. If the LED flashes green quickly, the charger cannot charge the  
batteries. Replace the batteries with new ones. Full battery charging can  
take up to 24 hours.  
Warning: Do not try to recharge alkaline batteries. Use C size NiMH rechargeable  
batteries. Failure to do so may damage the speakers or cause a fire. The speaker will  
try to charge batteries if the battery switch is set to NiMH.  
Note: Rechargeable batteries can be recharged with the speakers on or off. RF-WS-01  
and RF-WS-01-W cannot recharge any type of batteries. If you want to use  
rechargeable batteries in the RF-WS-01 or RF-WS-01-W, you must use a regular  
standalone charger to recharge batteries.  
Positioning the speakers  
Caution: To avoid the risk of electric shock and fire, and to prevent damage, locate  
the sender and speakers with no obstructions in front of the ventilation holes.  
Caution: Do not use the WS-01 or WS-03 in a wet environment. If you use the WS-02  
outdoors or in wet environment, do not connect the AC adapter.  
Note: if you need to mount the speakers, make sure that the left and right speakers  
are switched to the correct left, right, or mono setting for speaker output sound.  
Note: For best performance, the sender LED should face the general direction of the  
area where you plan to place the speakers.  
14  
 
Using your system  
Turning on your system  
To turn on the system:  
1
Move the Power switch to the ON position on the side panel of the  
sender. The green Link Status LED starts to blink slowly to indicate the  
sender is plugged in and in Standby mode.  
2
Press the Power switch on the front panel of the speakers. The green  
Status LED starts to flash to indicate the receiver is plugged in and in  
Standby mode.  
Note: If the speaker is operated by batteries and battery capacity is too low to power  
the speakers, the Low Battery Warning LED turns red to indicate a low battery  
warning.  
The sender and speakers were pre-paired in the factory. When an active  
link is established between them the green Link Status LEDs turn solid.  
Note: If the LEDs continue to blink after 30 seconds, it means there is no active link  
between the sender and speakers. Try to connect the system manually using the PAIR  
button. For more information see “Troubleshooting” on page 17.  
Listening to your system  
To listen to the system:  
1
Turn on the system. Make sure that there is an active link between the  
sender and speakers. When an active link is established between them  
the green Link Status LEDs turn solid.  
2
Turn on your audio source, then play the audio.  
To adjust the volume on the RF-WS01 or RF-WS01-W:  
Turn the volume knob on the speaker. The volume is adjusted  
independently regardless of channel setting (left, right, or mono).  
To adjust the volume on the RF-WS02:  
Turn the volume knob on the speaker. Make sure the speaker is switched  
to the correct left, right, or mono setting for speaker output sound.  
RF-WS01/WS01-W/WS02  
 
15  
 
Turning off the system  
To turn off the system:  
1
Move the sender Power switch to the OFF position. The Green Link  
Status LED goes off indicating that the sender is turned off.  
2
Push the Power switch on the front panel of each speaker. The Green  
Link Status Power LED goes off to indicate that the speaker is turned off.  
Speaker auto shut-off on RF-WS02 speakers  
When the speakers are running on battery power, they turn off  
automatically when the device they are connected to is turned off or  
does not send audio for more than five minutes. This feature  
conserves battery life.  
Optimizing your surround sound  
Your Rocketfish digital wireless speakers use state-of-the-art 2.4 GHz  
technology to digitally send audio data from the sender to the  
speakers. Wireless links create a small latency between the sender  
and receiver, and many A/V receivers let you adjust the delay  
between various speakers in your surround system. If using  
Rocketfish digital wireless speakers as part of a surround system, you  
can optimize your system when tuning your speaker setup by  
shortening the delay to the wireless speakers by 15-20ms.  
Low Battery warning  
The red Low Battery Warning LED is lit when there is no AC power  
and the battery capacity is not enough to power the speaker. Replace  
the old batteries with fresh Alkaline batteries, or charge your  
rechargeable batteries.  
Using Bass Boost (RF-WS02 only)  
Bass Boost enhances the low-end sound. If the Bass Boost button is  
pressed once, the unit enters Bass Boost mode, and the red Bass  
Boost LED is lit. If the Bass Boost button is pressed again, the unit  
exits Bass Boost mode and the red Bass Boost LED turns off.  
16  
 
Maintaining your system  
Use a soft cloth dampened with a weak solution of mild detergent  
and water. Dry the apparatus immediately afterwards with a clean  
cloth. Do not use abrasive cloth, thinners, alcohol, or other chemical  
solvents, because they may damage the finish or remove the panel  
lettering.  
Cautions:  
Do not cover the ventilation openings with items, such as newspapers,  
table clothes, and curtains.  
If the power cord is damaged, it must be repaired by a qualified repairer.  
Note:  
If the RS-WS02 becomes wet, you can drain water by gently tipping it  
slightly to one side for a few seconds.  
Troubleshooting  
Read this User Guide carefully before using your digital wireless  
speakers. Check this list for a possible troubleshooting solution  
before calling for service.  
Problem  
Solution  
No sound  
Make sure the sender AC adapter is connected to the sender, and either the  
speaker AC adapter is connected or fresh or charged batteries are installed  
in the speakers.  
Make sure that all cables are connected correctly. Check to see if the green  
Link Status LEDs illuminate on the front of both the sender and speaker  
units. If the green Link Status LEDs are lit solidly, the communication is  
working correctly and the audio cables from audio source to the sender  
should be checked. If the green Link Status LEDs are flashing or off, refer to  
the “No communication between sender and speaker” section below.  
RF-WS01/WS01-W/WS02  
 
17  
   
Problem  
Solution  
Sound interference  
Move your sender and speaker slowly to find the best reception position for  
your system.  
Shorten the distance to between your sender and speakers. The maximum  
distance is 55 feet (RF-WS01 or RF-WS01-W) or 100 feet (RF-WS02).  
Check to determine if there are any obvious radio frequency interference  
sources near your system.  
No communication  
between the sender  
and speaker  
Make sure that the power cords and/or batteries are connected or installed  
correctly.  
After the power switch is ON position and turn on both the sender and  
speaker, the front panel green Link Status LEDs should light. If they are lit  
solidly on, a communication link has been established between the units. If  
they are flashing or off on any of the units, press and hold the PAIR button  
on either the sender or speakers for more than three seconds. (The sender's  
and speakers PAIR buttons are located on rear panel of unit.) This will put  
the unit into “connection mode” for about 30 seconds. During this period  
the PAIR button on the other units must also be pressed for more than three  
seconds so that it will also enter “connection mode. The system proceeds  
with the connection process between sender and speaker. While in  
“connection mode, the green Link Status LEDs blink at a faster rate. When  
an active link is established between the sender and receiver, the LEDs will  
be solid on and will not blink.  
Note: Try pressing the PAIR buttons again if the green Link Status LEDs keep  
blinking after 30 seconds.  
Specifications  
Sender  
Audio Input: Stereo, line level Maximum 1Vrms or 2Vrms  
Audio Output: Wireless  
Stereo, 48 kHz uncompressed  
Bit-rate: 2.465 Mbps  
Raw wireless bit-rate: 2Mbps  
Supply Voltage  
Transmission Delay  
5V @ 200mA  
15-20mS  
18  
 
 
Speakers (RF-WS01 and RF-WS01-W)  
Audio Input: Wireless  
Stereo, 48 kHz uncompressed  
Bit-rate: 1.465 Mbps  
Raw wireless bit-rate: 2Mbps  
Audio Output  
8W (RMS) 2-way speaker full range system (10% THD)  
High Efficiency Class D speaker amplifier driving internal full range speakers  
Supply Voltage  
Power Consumption  
Transmission Delay  
12V @ 1.0A  
12W  
15-20mS  
Speakers (RF-WS02)  
Audio Input: Wireless  
Stereo, 48 kHz uncompressed  
Bit-rate: 1.465 Mbps  
Raw wireless bit-rate: 2Mbps  
Audio Output  
20W (RMS) bi-amp speaker full range system (10% THD)  
High Efficiency Class D speaker amplifier driving internal full range speakers  
Supply Voltage  
Power Consumption  
Transmission Delay  
15V @ 1.2A  
18W  
15-20mS  
Legal notices  
FCC Part 15 [short version--keep?]  
This device complies with Part 15 of the FCC Rules. Operation of this  
product is subject to the following two conditions: (1) this device may  
not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause  
undesired operation.  
RF-WS01/WS01-W/WS02  
 
19  
 
This equipment has been tested and found to comply within the  
limits for a class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
• Consult the dealer or an experienced technician for help.  
FCC warning  
Changes or modifications not expressly approved by the party  
responsible for compliance with the FCC Rules could void the user’s  
authority to operate this equipment.  
IC RSS210 STATEMENT  
Operation is subject to the following two conditions: (1) this device  
may not cause interference, and (2) this device must accept any  
interference, including interference that may cause undesired  
operation of the device.  
Canada ICES-003 statement  
This Class B digital apparatus complies with Canadian ICES-003.  
20  
 
Information for Users on Disposal of Old Equipment  
[European Union]  
Note: This symbol is only valid in the European Union.  
This symbol indicates that the electrical and electronic  
equipment should not be disposed as general household  
waste at its end-of-life. Instead, the product should be handed  
over to the applicable collection point for the recycling in accordance  
with your national legislation.  
By disposing of this product correctly, you will help to conserve  
natural resources and will help prevent potential negative effects on  
the environment and human health that could otherwise be caused  
by inappropriate waste handling of this product. For more  
information about collection point and recycling of this product,  
please contact your local municipal office, your household waste  
disposal service or the shop where you purchased the product.  
Penalties may be applicable for incorrect disposal of this waste, in  
accordance with national legislation.  
[Other Countries Outside the European Union]  
If you wish to dispose of this product, please do so in accordance  
with applicable national legislation or other rules in your country for  
the treatment of old electrical and electronic equipment.  
RF-WS01/WS01-W/WS02  
 
21  
22  
 
One-Year Limited Warranty  
Rocketfish Products (“Rocketfish”) warrants to you, the original purchaser of this new  
RF-WS01/RF-WS01-W/WS02 (“Product”), that the Product shall be free of defects in the  
original manufacture of the material or workmanship for one (1) year from the purchase of the  
Product (“Warranty Period”). This Product must be purchased from an authorized dealer of  
Rocketfish brand products and packaged with this warranty statement. This warranty does not  
cover refurbished Product. If you notify Rocketfish during the Warranty Period of a defect  
covered by this warranty that requires service, terms of this warranty apply.  
How long does the coverage last?  
The Warranty Period lasts for one year (365 days), beginning on the date you purchased the  
Product. The purchase date is printed on the receipt you received with the product.  
What does this warranty cover?  
During the Warranty Period, if the original manufacture of the material or workmanship of the  
Product is determined to be defective by an authorized Rocketfish repair center or store  
personnel, Rocketfish will (at its sole option): (1) repair the Product with new or rebuilt parts; or  
(2) replace the Product at no charge with new or rebuilt comparable products or parts. Products  
and parts replaced under this warranty become the property of Rocketfish and are not returned  
to you. If service of Products and parts are required after the Warranty Period expires, you must  
pay all labor and parts charges. This warranty lasts as long as you own your Rocketfish Product  
during the Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the  
Product.  
How to obtain warranty service?  
If you purchased the Product at a retail store location, take your original receipt and the Product  
to the store you purchased it from. Make sure that you place the Product in its original  
packaging or packaging that provides the same amount of protection as the original  
packaging. If you purchased the Product from an online web site, mail your original receipt and  
the Product to the address listed on the web site. Make sure that you put the Product in its  
original packaging or packaging that provides the same amount of protection as the original  
packaging.  
Where is the warranty valid?  
This warranty is valid only to the original purchaser of the Product in the United States, Canada,  
and Mexico.  
What does the warranty not cover?  
This warranty does not cover:  
Customer instruction  
Installation  
Set up adjustments  
Cosmetic damage  
RF-WS01/WS01-W/WS02  
 
23  
 
Damage due to acts of God, such as lightning strikes  
Accident  
Misuse  
Abuse  
Negligence  
Commercial use  
Modification of any part of the Product, including the antenna  
This warranty also does not cover:  
Damage due to incorrect operation or maintenance  
Connection to an incorrect voltage supply  
Attempted repair by anyone other than a facility authorized by Rocketfish to service the  
Product  
Products sold as is or with all faults  
Consumables, such as fuses or batteries  
Products where the factory applied serial number has been altered or removed  
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY.  
ROCKETFISH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR  
THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT  
NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST  
PROFITS. ROCKETFISH PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO  
THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING, BUT  
NOT LIMITED TO, ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD  
SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER  
THE WARRANTY PERIOD. SOME STATES, PROVINCES AND JURISDICTIONS DO NOT ALLOW  
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY  
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO  
HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.  
Contact Rocketfish:  
For customer service please call 1-800-620-2790  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Avenue South, Richfield, Minnesota, U.S.A. 55423-3645  
© 2008 Best Buy Enterprise Services, Inc.  
All rights reserved. ROCKETFISH is a trademark of Best Buy Enterprise Services, Inc. Registered in  
some countries. All other products and brand names are trademarks of their respective owners.  
24  
 
RF-WS01/WS01-W/WS02  
25  
 
26  
 
RF-WS01/WS01-W/WS02  
27  
 
(800) 620-2790  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Avenue South, Richfield, MN 55423-3645 USA  
© 2008 Best Buy Enterprise Services, Inc.  
All rights reserved. ROCKETFISH is a trademark of Best Buy Enterprise Services, Inc.  
All other products and brand names are trademarks of their respective owners.  
ENGLISH  
08-1669  
 

Radio Shack CD Player 32 3043 User Guide
Radio Shack Clock 63 973 User Guide
RCA IP Phone IP120 User Guide
RoboteQ TV Converter Box AX2550 2850 User Guide
Roper Range 336 User Guide
Rowenta Hair Dryer PH570 User Guide
Samson Music Mixer XM 410 User Guide
Samsung Clothes Dryer DV210AEW User Guide
Samsung CRT Television CL21M6W, CL25M6W, CL29V5W, CL29M6W, CL29M9W, CL21A8W, CL21S8W, CL29K3W, CL29D8W, CL29D9W, CL25M5W, CL29M5W User Guide
Sears Saw 11329003 User Guide